How To Repair A Chip In A Bootz Tub

Download Article

Download Article

Fixing a chipped bathtub is a do-it-yourself project that will save y'all from hiring an expensive professional. Whether your tub but has a few small fries, or it is badly damaged and needs to be refinished, these are both projects that you will find kits for at your local dwelling house improvement shop. With a little elbow greasy, your tub volition wait similar new in just a matter of days!

1. 1

   Buy a 2-component epoxy kit for scrap repair. Look in the adhesive or bathroom repair section of a dwelling hardware store. Purchase a kit that comes with both the catalyst and hardener that you will mix together to create the epoxy.^[1]

   • Almost epoxy flake repair kits come in shades of white to match the most common color of bathtubs. Try to choose a kit that will closely match the shade of your bathtub, or 2 kits that yous can mix together to create the correct color.
   • Epoxy repair kits work to fix chips in all kinds of bathtubs including ceramic, porcelain, acrylic, fiberglass, and enamel tubs.

2. 2

   Scrub the damaged area with a sponge and soap or tub cleaner, and then dry it. Use warm water and dish detergent or a household tile and tub cleaner to make clean the chipped surface area. Thoroughly dry out the area with a clean rage afterwards you lot finish cleaning it.^[2]

   • Yous can also use acetone or rubbing alcohol to clean the area. Any product that removes grease and soap scum will work to clean the chip.

   Advert

3. 3

   Follow the directions on your epoxy kit to mix the 2 components together. Some epoxy kits come with a mixing tray and stirring stick for you to use. Mix the epoxy in a disposable tray with a toothpick or matchstick if your kit didn't come up with the mixing supplies.^[3]

   • Information technology's a skillful idea to set the tray on a piece of paper-thin or some scraps of paper to grab any spills.

4. 4

   Apply the epoxy to the flake with a small-scale spatula, pigment castor, or bottom of a matchstick. Scoop up a modest amount of the epoxy with your chosen utensil. Spread it carefully in a sparse layer over the bit by working in ane management and shine out any spots where it pools.^[4]

   • Make sure that annihilation yous use to utilise the epoxy is disposable. It will exist difficult to become the epoxy off of anything it touches.
   • Information technology'southward easiest to first with a small amount of epoxy and add more layers than it is to put too much on and remove it.

5. v

   Let the epoxy dry, and so sand downward the surface with 400-600 grit sandpaper. Follow the directions on your epoxy kit to let it fully dry out. Gently sand the surface with 400- or 600-grit sandpaper until it feels smooth similar the rest of the tub.^[5]

   • Some epoxy will set in two-three hours, at which point you can sand. Other kits may advise you to await up to 24 hours before sanding.
   • Y'all can add another layer of epoxy afterwards sanding if you can notwithstanding experience the chip. Then repeat the process.
   • Keep in listen that while this is will assist hibernate pocket-sized chips, you lot may nonetheless exist able to detect the patch. This will be especially obvious if yous endeavour to fill a number of fries with the epoxy.^[6]

   Advertisement

1. i

   Buy a bathtub refinishing kit at a dwelling house improvement centre. Save yourself fourth dimension by buying a whole kit that has everything you need to refinish your tub. Almost kits come up with tub cleaner, sandpaper, primer, refinishing paint, a paint tray, a brush, and a roller.^[seven]

   • Bank check that the kit comes with a durable resin coating for your tub. Some cheaper kits come with an epoxy coating, which chips and discolors faster.
   • Refinishing kits tin can price from about $30-$100 USD.
   • Tub refinishing kits work to refinish all kinds of bathtubs including ceramic, porcelain, acrylic, fiberglass, and enamel tubs. The kits will provide a new porcelain-like terminate to these kinds of tubs.

2. 2

   Ventilate the bathroom, encompass the floors, and put on protective gear. Open upwards all the windows and put a fan in the bathroom to ventilate it. Encompass the floors with heavy-duty plastic sheets to keep them safe during the refinishing process. Put on a confront mask and goggles.^[8]

   • You lot can too curtain plastic sheets over fixtures like the toilet and sink to protect them.

3. 3

   Clean the bathtub with the cleaner from the kit. Read the directions on the cleaner to apply it to the tub and use a sponge to scrub the tub make clean. Rinse the tub out, then go over it with the sponge and cleaner 2 more times to remove any lather scum and stains earlier you lot refinish it.^[nine]

   • If your kit did non come with cleaner, then buy an industrial strength bathtub cleaner to utilise.
   • Allow the tub completely air dry out, or speed upwards the procedure with towels and a hair dryer.

4. 4

   Sand the whole tub with the sandpaper in your kit to remove the old finish. Start with the everyman-grit sandpaper from your refinishing kit and sand the whole surface of the tub in circular motions by mitt, or with an electrical sander. Piece of work your style up to the highest-dust sandpaper in your kit until the tub is completely smooth.^[10]

   • Your refinishing kit should come with sandpaper to use. If your kit didn't come with sandpaper, then outset with 400-grit sandpaper and work your fashion upwards to 2000-dust. Increase the grit of the sandpaper in increments of 200 until you reach yard-grit sandpaper, then get upwardly in increments of 500 until you end using 2000-grit sandpaper.

5. 5

   Repair any fries or cracks in the tub with a ii-component epoxy flake repair kit. Follow the instructions to mix the two parts of the epoxy in a pocket-size tray. Use a pocket-size brush, spatula, or the bottom end of a matchstick to apply sparse layers of epoxy to any chips. Expect ii-3 hours until the epoxy dries and sand the patches down with 2000-grit sandpaper to lucifer the cease of the rest of the tub.^[11]

   • This will ensure that the tub has no chips or cracks and seal the surface before you apply the new finish.
   • Get a two-component epoxy chip repair kit from the bathroom remodeling or adhesive department of a home improvement store if your kit did not come with information technology.

6. 6

   Put painter's tape on the walls and around whatsoever plumbing equipment. Record along the edges of the tub where they touch the walls and around the faucet and other fixtures. Fifty-fifty if you lot have a steady mitt, it's easy for paint to get astray!^[12]

   • Painter's tape is the blue masking tape that you lot tin can observe at hardware and paint stores.

7. 7

   Apply 1 coat of primer with a brush and roller. Utilise a roller to roll on the primer onto the large, apartment sections of the tub similar the floor and sides, and so employ a castor to get into the corners and curved parts. Let it dry out for at least 2-three hours before yous start to paint on the new finish.^[thirteen]

   • Priming the surface is an of import office of ensuring that the new finish adheres correctly and then that you finish up with the correct texture. Make sure that the primer is completely dry to the touch before you paint over information technology.

8. 8

   Paint on 2-three coats of the new stop with a castor and roller. Always paint in i direction when y'all use the new glaze to your tub. Curl on the new finish to the floors and sides in even back-and-forth rolls until the flat surface area is completely covered. Fill in the corners and curves of the tub with even back-and-forth castor strokes. Let each coat dry for at least 30 minutes before you put the next coat on.^[14]

   • Some kits may come up with a spray-on terminate. If you lot utilise a sprayer instead of a castor or roller, attempt to spray evenly and in 1 direction. Make sure your walls and fixtures are well-protected by tape where in that location is a risk of paint spray hitting them.

9. 9

   Let your bathtub sit down for 2-3 days before you use information technology. The new finish needs to prepare completely before you run water over it. Consult your kit's directions for the exact drying time for your specific finish.^[xv]

   • If you don't allow the finish dry long enough, yous could end up with streaks and bubbling in the new coating and you will need to start the procedure once more.
   • Your new DIY end volition last for years, only keep in mind that professional person finishes volition last even longer.
   • The chemicals used in this procedure tin can be unsafe, so it may be a skillful idea to stay somewhere else for a few days while the tub cures.^[16]

   Advertisement

Add together New Question

• Question

  How do you set a fleck in a porcelain tub?

  

  Art Fricke
  Home Renovation & Repair Specialist

  Art Fricke is a dwelling renovation and repair specialist and the owner of Art Tile & Renovation based in Austin, Texas. With over x years of experience, he specializes in bathroom and kitchen renovations. Fine art focuses on a single contractor arroyo to customized renovation work, and performs projects such as installing custom tile showers, fixing tiled shower leaks, replacing cracked tiles, and installing floor and wall tile.

  

  Home Renovation & Repair Specialist

  Proficient Answer

  

  Back up wikiHow by unlocking this expert answer.

  If y'all just have a small, isolated bit, you lot tin can go enamel gear up from a home improvement store. Just dab a little on, then permit it dry out. Withal, keep in mind that you'll probably still be able to encounter the patch, especially if you lot're trying to cover a number of chips.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertising

Things Y'all'll Demand

• 2-component epoxy fleck repair kit
• Sponge
• Soap or household tub and tile cleaner
• Disposable tray and mixing stick
• Minor spatula, brush, or matchstick
• 400-600 grit sandpaper

• Bathtub refinishing kit (tub cleaner, sandpaper, primer, refinishing pigment, a paint tray, a castor, and a roller)
• 2-component epoxy chip repair kit
• Small spatula, brush, or matchstick
• Face mask
• Goggles
• Fan
• Heavy-duty plastic sheets
• Painter'southward tape

• If you lot don't want to refinish your bathtub on your own, you tin rent a professional who'southward specialized in refinishing tubs, instead.^[17]

Advertisement

About This Article

Article Summary 10

If you have a pocket-size chip in your bathtub, you tin gear up it with an epoxy kit. Before you beginning, scrub the damaged area of your tub make clean with a sponge and some soap and h2o. Follow the directions on your epoxy kit for mixing the 2 components together. Once they're mixed, use a small spatula or a paintbrush to spread a sparse layer of the epoxy over the chip. Await for information technology to fully dry, which should have at least 2-3 hours, then utilise sandpaper to vitrify out the stale epoxy until its smooth. If your bathtub is badly damaged, yous can utilize a bathtub refinishing kit to restore the finish. You'll need to sand the whole tub to remove the former finish, repair all the cracks with epoxy, then paint on new primer and finish. To larn how to prevent paint from getting on you tile, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 79,028 times.

Did this article help you?

Source: https://www.wikihow.com/Fix-a-Chipped-Bathtub

Posted by: muellerpory1963.blogspot.com

Share this post